Ne parlammo già qui
4k
Hdr
120hz
4:4:4
10-12bit
Gsync
Freesync
2.1
5.1
Dovrebbe essere tutto...
Cosa vi interessa di questa roba?
Se volete tutto tutto, iniziare a massaggiarsi il rene buono, perché dovrà fare il doppio lavoro.
SOLO RIGUARDO L'AUDIO (quindi escludendo tutta o gran parte delle cose elencate sopra)
Dipende cosa ti serve di quella lista.
Se vuoi tutto, la risposta è semplice: [Edit. leggi sotto]
_ogni_ anello della catena deve essere hdmi2.1.
Ps. mi correggo, lato amp è importante che abbia l'earc se vuoi audio non compresso.
Per l'hdmi 2.1 non dovrebbero esserci problemi, è retrocompatibile, e non dovendo fare il pass-through video (cagata pazzesca col senno di poi infatti io stesso uso l'earc), ma solo audio, dovrebbe esser sufficiente un cavo HDMI 2.0.
Condizionale perché questa combinazione non l'ho provata.
Tl;dr: se l'amp (e TV!) ha l'earc compra il tv e vedi se riesci a far tutto quel che dico sopra. 99 su 100 dovrebbe funzionare.
No earc, devi segare l'audio.
Pps. "ARC fallback"
Is HDMI eARC Backwards Compatible with HDMI ARC?
This depends on what you mean by backwards compatible. HDMI eARC has ARC fallback, meaning that if you hook up one device with HDMI eARC with another device that doesn’t support it, the devices will fallback to broadcasting an HDMI ARC signal instead.
This means your audio device will not be automatically discovered, and you will have to initiate the digital handshake manually. This also means it will be broadcasting with a maximum bandwidth of 1 Mbps rather than 37 Mbps, meaning no lossless surround sound.
If, however, you are connecting two HDMI eARC capable devices with an HDMI 2.0 or lower cable, you might not get it to work. The results of doing so are unclear and may depend on the devices themselves, though it is unlikely you will damage your equipment by using the wrong HDMI cable since the pin configuration and plug shape are the same.
Your best bet, as always, is to make the inexpensive upgrade to an ultra-high-speed HDMI 2.1 or higher cable.
https://thehometheaterdiy.com/hdmi-arc-and-earc/Infine, per dare un'idea di come "funzioni", e chiudo: personalmente ho assemblato tutta la filiera nel modo idealmente meno micragnoso, vale a dire -come dicevo- con tutti i pezzi certificati hdmi 2.1 (pc, x2 cavi, tv, avr).
Ma ogni 2x3 ci sono comunque cazzi. Ogni tanto la codifica impazzisce, o il gsync o chissà cos'altro.
Solo due giorni fa l'avr ha iniziato a segnarmi come frequenza di campionamento 2.8Mhz anzichè 192khz. Googolando scopro che il primo è un valore associato alla codifica dsd, robba per audiofili. In linea teorica è un valore decisamente migliore e probabilmente è solo un errore dell'interfaccia, ma essendo la prima volta che mi capitava in mesi di utilizzo, l'ho bollata come anomalia.
E riavvia tv, e pc, e avr. e reinstalla driver video. Zero, non cambiava un tubo.
Soluzione: spegnere la ciabatta, disalimentando la qualunque.
Risolto :'D.
99 su 100 tutto 'sto merdaio inciampa proprio sugli handshake tra i vari dispositivi. Se la sequenza e la catena non è rispettata, qualcosa prima o poi salterà.
Solo per dire che se così è già un casino, figurarsi mescolando cose di varie generazioni.
Magari poi ti va bene, lo spero per te: uomo avvisato.
Regola aurea dall'avr forum:
HDMI handshake issues can occur with all brands but can often be mitigated by powering on the HDMI components in a specific order and allowing a few seconds between each for a proper handshake to occur:TV ........ pause 5 seconds ..........AVR .............. pause 5 seconds ...............sourceOtherwise, what also works is changing to a different station and back (if using a cable/sat box) or changing to a different source entirely and back.